[Techtoolslist] [Vectorlist] Updating - W-G 6100 Vector Monitor FAQ & Guide V1.1

[mike hooker]

data east pinball power supply HV transistors work well too. i think thy are  mje15031 and 15030. you do have to swap the legs. i mount them, and solder jumper leads from the legs to the board. much easier than twisting the legs. 


----- Original Message -----
From: colin.w.davies via Techtoolslist <techtoolslist at flippers.com>
Reply-To: Technical Tools Mail List <techtoolslist at flippers.com>
To: Discussons of vector-based arcade games. <vectorlist at lists.vectorlist.org>
Cc: colin.w.davies <colin.w.davies at btopenworld.com>, <techtoolslist at flippers.com>
Sent: 12/6/2023 7:19:35 PM
Subject: Re: [Techtoolslist] [Vectorlist] Updating - W-G 6100 Vector Monitor FAQ & Guide V1.1
________________________________________________________________________________

Bd237 and Bd238 seem to work well but you have to shuffle the legs around.  (Think pin 2 and 3 are swapped). Cheap and easy to find.Sent from my Galaxy
-------- Original message --------From: John Robertson <jrr at flippers.com> Date: 06/12/2023  22:26  (GMT+00:00) To: "Discussons of vector-based arcade games." <vectorlist at lists.vectorlist.org> Cc: techtoolslist at flippers.com Subject: [Vectorlist] Updating - W-G 6100 Vector Monitor FAQ & Guide V1.1 
    Who is maintaining this?
    I ask because on page 8 there is a typo - that I've only just
      realized when I was going through trying to update my WG monitors
      as we have a pair of SWs that are running WGs (with the LV2000
      kits).
    It says "R701 (1.3K) changed from +/-2%, 1/4W to +/-1%, 5W.(*)"
    That can't be right, I am certain it should instead say:
    "R701 (1.3K) changed from +/-2%, 1/4W to +/-1%, 0.5W.(*)"
    and it would be clearer with:
    "R701 (1.3K) changed from +/-2%, 1/4W to +/-1%, 1/2W.(*)"
    It makes no sense otherwise. There simply can't be enough current
      for a 5W resistor as this is ground biasing the base of a small
      signal transistor.
    Then there is the question of Q604/Q704 (MPSU07) transistors
      upgraded to TO-202 (NTE-49) which looks like another problem as
      there is no NTE-49 and hasn't been for decades. That was the same
      as the ECG-49, which was a NPN-Si, 125Vcbo, 2A, Gen Purpose
      TO-202. Anyone have a workable replacement to save me the lookup
      time? 
    
    I'm thinking a Rv1.2 is overdue...
    John :-#)#
    
    -- 
                 John's Jukes Ltd. 
7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3 
Call (604)872-5757 (Pinballs, Jukes, Video Games)
                 flippers.com 
"Old pinballers never die, they just flip out"
  

_______________________________________________
Techtoolslist mailing list
Techtoolslist at flippers.com
https://pairlist7.pair.net/mailman/listinfo/techtoolslist
FTP site is: ftp://ftp.flippers.com/TTL/TestEquipment
Archive site 2005-Current: https://seven.pairlist.net/pipermail/techtoolslist/
Vectorlist Archives 1997/99 - 2016: https://www.vectorlist.org/